A Spyder electro-mechanical hybrid with selectable modes, bridging budget mechanical and electronic play.
Technical Specifications
Operation
Electropneumatic-assisted blowback
Firing Modes
semi-auto, ramping, full-auto
Caliber
.68
Feed System
Gravity hopper
Air Source
HPA/CO2
Operating Pressure
~300 psi
Weight (unloaded)
2.4 lbs
Street Price
$80-140 (used)
Maintenance
Low
Notable features: Selectable modes, EKO valve, Light body
Pros & Cons
Pros
Cheap multi-mode
Light
Reasonable efficiency
Cons
Discontinued
Lower build tier
Best for: Budget upgraders, Rec play, Used buyers
Setup & First-Day Tuning Guide
Charge Batteries 24 Hours Before — Charge the Spyder Clone's battery fully before your first session. Bring a spare — a low battery causes dump-fire and board errors that mimic broken gun symptoms.
Lube Bolt & Carrier Before Air — Slide the bolt back by hand — it should move freely. Apply Dow 33 to all bolt and carrier O-rings. Never lube the solenoid.
Set Operating Pressure to Spec — The Spyder Clone runs at ~300 psi. Set your HPR per the manual — never exceed rated pressure.
Chronograph via HPR, Then Dwell — With eyes ON, fire 5 shots and read the chrono. Adjust HPR to approach your target velocity (usually 280 fps). Change dwell (1ms at a time) only after HPR is dialed.
Keep Anti-Chop Eyes ON — Turn eyes ON for your first outing. A slight hesitation is normal — a force-feed loader (Dye Rotor, Virtue Spire) eliminates it entirely.
Set Firing Mode Before the Field — Set the gun to semi-auto mode. Most recreational fields enforce semi-auto — confirm mode is correct before your first game.
Maintenance Schedule
Interval
Task
Detail
After every outing
Barrel, bolt & exterior clean
Squeegee twice, bolt wipe, screws snug. Clean eye ports with a dry cotton swab.
Every 5 sessions
Bolt O-ring lube & cup seal check
Clean with isopropyl, dry, apply Dow 33. Inspect cup seal — replace if deformed.
Every 6 months
Valve & fitting service
Re-lube all O-rings. Check all fittings and inline regulator if present.
Annually
Full teardown & O-ring replacement
Complete disassembly, full O-ring kit replacement, inspect springs.
Simple internals; manage battery and o-rings.
Common Problems & Troubleshooting
Wide velocity spread
Cause: Worn bolt O-rings (most common); LPR drift
Fix: Bolt carrier O-ring wear is the #1 cause of inconsistency in guns like the Spyder Clone. Remove bolt, inspect O-rings, re-lube or replace as a set.
Gun won't power on
Cause: Low battery voltage; terminal corrosion
Fix: Test battery — should read 9V+ (alkaline) or 7.4V+ (LiPo). Clean terminals with isopropyl. Check the manual for the factory reset sequence.
Air dumps continuously
Cause: Solenoid failure; low battery
Fix: De-gas immediately. Check battery first — low voltage causes dump-fire. If battery is good, inspect solenoid for debris or O-ring failure.
Double-firing / bounce
Cause: Dwell too high; debounce too sensitive
Fix: Reduce dwell 1ms at a time until resolved. Never go below 4ms on spool guns.
Eyes not working with eyes on
Cause: Paint residue blocking eye ports
Fix: Clean eye ports with a dry cotton swab — this fixes 95% of apparent eye failures.
Firing mode won't change
Cause: Board lock mode
Fix: Download the board manual PDF — the unlock sequence is a button-hold pattern during power-on.
Upgrade Path
Barrel
Spring kit
Bolt
Frequently Asked Questions
Is the Spyder Clone good for beginners?
Yes — the Spyder Clone is an excellent first-time gun. It's durable and forgiving of beginner mistakes.
Does the Spyder Clone run on CO2 or HPA?
Compatible with HPA/CO2. HPA is required — CO2 can damage solenoid O-rings on electropneumatic guns.
What is the operating pressure of the Spyder Clone?
The Spyder Clone operates at ~300 psi. Match your regulator output to this spec.
How hard is the Spyder Clone to maintain?
Easy — basic bolt cleaning every few sessions. Simple internals; manage battery and o-rings.
What loader does the Spyder Clone need?
A force-feed loader (Dye Rotor, Virtue Spire) is needed for the Spyder Clone's fire rate. A gravity hopper limits you to ~6 BPS.
How much does the Spyder Clone cost?
New: $N/A MSRP, typically $80-140 (used) on the street. Used prices vary — check BST forums and eBay for current asking prices.
What barrel thread does the Spyder Clone use?
The Spyder Clone shoots .68 caliber. Confirm the specific thread pattern for your variant before ordering a barrel.