Browse guns
Collections
SP / GOG Shocker AMP. Ultimate Guide
A modern revival of the iconic Shocker line: a tool-less spool gun with a smooth shot and a strong value-to-flagship ratio.
SP / GOG Shocker AMP Technical Specifications
| Operation | Electropneumatic spool |
|---|---|
| Firing Modes | semi-auto, ramping (all) |
| Caliber | .68 |
| Feed System | Force-fed |
| Air Source | HPA |
| Operating Pressure | ~160 psi |
| Weight (unloaded) | 2 lbs |
| MSRP | $900 |
| Street Price | $850-1000 |
| Maintenance | Moderate |
Notable features: Tool-less bolt, On/off regulator, Refined frame
Pros & Cons
Pros
- Iconic platform
- Smooth efficient shot
- Good value high-end
Cons
- Spool maintenance
- Smaller current dealer base
Best for: Tournament players, Shocker fans, Value high-end buyers
Setup & First-Day Tuning Guide
- Charge Batteries 24 Hours Before. Charge the SP / GOG Shocker AMP's battery fully before your first session. Bring a spare. A low battery causes dump-fire and board errors that mimic broken gun symptoms.
- Lube Bolt & Carrier Before Air. Slide the bolt back by hand. It should move freely. Apply Dow 33 to all bolt and carrier O-rings. Never lube the solenoid.
- Set Operating Pressure to Spec. The SP / GOG Shocker AMP runs at ~160 psi. Set your HPR per the manual. Never exceed rated pressure.
- Chronograph via HPR, Then Dwell. With eyes ON, fire 5 shots and read the chrono. Adjust HPR to approach your target velocity (usually 280 fps). Change dwell (1ms at a time) only after HPR is dialed.
- Keep Anti-Chop Eyes ON. Turn eyes ON for your first outing. A slight hesitation is normal. A force-feed loader (Dye Rotor, Virtue Spire) eliminates it entirely.
- Set Firing Mode Before the Field. Set the gun to semi-auto mode. Most recreational fields enforce semi-auto. Confirm mode is correct before your first game.
Maintenance Schedule
| Interval | Task | Detail |
|---|---|---|
| After every session | Barrel, bolt & eye port clean | Squeegee twice, bolt and carrier wipe. Clean eye ports with a dry cotton swab. |
| Every 5 sessions | Bolt & carrier O-ring service | Clean O-rings with isopropyl, dry, apply Dow 33. Inspect solenoid externally. Plunger should be clean and dry. |
| Every season | LPR service | Remove LPR, clean piston and O-rings, re-lube. 20-minute job that significantly improves consistency. |
| Annually | Full service | All O-rings replaced. Board terminals cleaned. Solenoid externally cleaned with contact cleaner (not lube). Firmware update if available. |
Tool-less bolt; periodic o-ring re-lube.
Common Problems & Troubleshooting
- Wide velocity spread
- Cause: Worn bolt O-rings (most common); LPR drift
- Fix: Bolt carrier O-ring wear is the #1 cause of inconsistency in guns like the SP / GOG Shocker AMP. Remove bolt, inspect O-rings, re-lube or replace as a set.
- Gun won't power on
- Cause: Low battery voltage; terminal corrosion
- Fix: Test battery. Should read 9V+ (alkaline) or 7.4V+ (LiPo). Clean terminals with isopropyl. Check the manual for the factory reset sequence.
- Air dumps continuously
- Cause: Solenoid failure; low battery
- Fix: De-gas immediately. Check battery first. Low voltage causes dump-fire. If battery is good, inspect solenoid for debris or O-ring failure.
- Double-firing / bounce
- Cause: Dwell too high; debounce too sensitive
- Fix: Reduce dwell 1ms at a time until resolved. Never go below 4ms on spool guns.
- Eyes not working with eyes on
- Cause: Paint residue blocking eye ports
- Fix: Clean eye ports with a dry cotton swab. This fixes 95% of apparent eye failures.
- Firing mode won't change
- Cause: Board lock mode
- Fix: Download the board manual PDF. The unlock sequence is a button-hold pattern during power-on.
Upgrade Path
- Bolt upgrades
- Barrel
- Board
SP / GOG Shocker AMP Paintball Gun FAQ
Is the SP / GOG Shocker AMP good for beginners?
The SP / GOG Shocker AMP has complex internals and is best for players who've already completed at least one season.
Does the SP / GOG Shocker AMP run on CO2 or HPA?
Compatible with HPA. HPA is required. CO2 can damage solenoid O-rings on electropneumatic guns.
What is the operating pressure of the SP / GOG Shocker AMP?
The SP / GOG Shocker AMP operates at ~160 psi. Match your regulator output to this spec.
How hard is the SP / GOG Shocker AMP to maintain?
Moderate. Regular bolt and eye-port cleaning, plus annual LPR service. Tool-less bolt; periodic o-ring re-lube.
What loader does the SP / GOG Shocker AMP need?
A force-feed loader (Dye Rotor, Virtue Spire) is needed for the SP / GOG Shocker AMP's fire rate. A gravity hopper limits you to ~6 BPS.
How much does the SP / GOG Shocker AMP cost?
New: $900 MSRP, typically $850-1000 on the street. Used prices vary. Check BST forums and eBay for current asking prices.
What barrel thread does the SP / GOG Shocker AMP use?
The SP / GOG Shocker AMP shoots .68 caliber. Confirm the specific thread pattern for your variant before ordering a barrel.
What firing modes does the SP / GOG Shocker AMP support?
Supported modes: semi-auto, ramping (all). Most recreational fields require semi-auto only.
How heavy is the SP / GOG Shocker AMP?
2 lbs unloaded. With a full hopper and HPA tank, expect roughly 4.5-5.5 lbs total.
Is the SP / GOG Shocker AMP worth buying?
A modern revival of the iconic Shocker line: a tool-less spool gun with a smooth shot and a strong value-to-flagship ratio. Strengths: Iconic platform, Smooth efficient shot. Trade-offs: Spool maintenance, Smaller current dealer base.
Compare prices and see live listings on the SP / GOG Shocker AMP gun page.