Best for: Collectors, Mechanical/pump enthusiasts, Autococker devotees
Setup & First-Day Tuning Guide
Charge Batteries 24 Hours Before — Charge the Inception Designs Autococker (custom)'s battery fully before your first session. Bring a spare — a low battery causes dump-fire and board errors that mimic broken gun symptoms.
Lube Bolt & Carrier Before Air — Slide the bolt back by hand — it should move freely. Apply Dow 33 to all bolt and carrier O-rings. Never lube the solenoid.
Set Operating Pressure to Spec — The Inception Designs Autococker (custom) runs at ~200-250 psi. Set your HPR per the manual — never exceed rated pressure.
Chronograph via HPR, Then Dwell — With eyes ON, fire 5 shots and read the chrono. Adjust HPR to approach your target velocity (usually 280 fps). Change dwell (1ms at a time) only after HPR is dialed.
Keep Anti-Chop Eyes ON — Turn eyes ON for your first outing. A slight hesitation is normal — a force-feed loader (Dye Rotor, Virtue Spire) eliminates it entirely.
Set Firing Mode Before the Field — Set the gun to semi-auto mode. Most recreational fields enforce semi-auto — confirm mode is correct before your first game.
Maintenance Schedule
Interval
Task
Detail
After every session
Full barrel, bolt & breech clean
Complete barrel clean (squeegee + patch), bolt and carrier wipe, breech patch. Clean eye ports with a dry cotton swab.
Every 3 sessions
LPR & HPR pressure check
Verify LPR output with a gauge. More than 5 psi drift indicates piston O-ring wear.
All O-rings replaced as a set. Full regulator rebuild kits. Solenoid rebuild. Board firmware update.
Cocker timing (three-way, ram, valve) requires periodic adjustment and skill.
Common Problems & Troubleshooting
Wide velocity spread
Cause: Worn bolt O-rings (most common); LPR drift
Fix: Bolt carrier O-ring wear is the #1 cause of inconsistency in guns like the Inception Designs Autococker (custom). Remove bolt, inspect O-rings, re-lube or replace as a set.
Gun won't power on
Cause: Low battery voltage; terminal corrosion
Fix: Test battery — should read 9V+ (alkaline) or 7.4V+ (LiPo). Clean terminals with isopropyl. Check the manual for the factory reset sequence.
Air dumps continuously
Cause: Solenoid failure; low battery
Fix: De-gas immediately. Check battery first — low voltage causes dump-fire. If battery is good, inspect solenoid for debris or O-ring failure.
Double-firing / bounce
Cause: Dwell too high; debounce too sensitive
Fix: Reduce dwell 1ms at a time until resolved. Never go below 4ms on spool guns.
Eyes not working with eyes on
Cause: Paint residue blocking eye ports
Fix: Clean eye ports with a dry cotton swab — this fixes 95% of apparent eye failures.
Firing mode won't change
Cause: Board lock mode
Fix: Download the board manual PDF — the unlock sequence is a button-hold pattern during power-on.
Upgrade Path
Custom barrels
Pump kits
Regulators
Cosmetic milling
Frequently Asked Questions
Is the Inception Designs Autococker (custom) good for beginners?
The Inception Designs Autococker (custom) has complex internals and is best for players who've already completed at least one season.
Does the Inception Designs Autococker (custom) run on CO2 or HPA?
Compatible with HPA. HPA is required — CO2 can damage solenoid O-rings on electropneumatic guns.
What is the operating pressure of the Inception Designs Autococker (custom)?
The Inception Designs Autococker (custom) operates at ~200-250 psi. Match your regulator output to this spec.
How hard is the Inception Designs Autococker (custom) to maintain?
Advanced — plan for regular O-ring replacement and annual solenoid service. Cocker timing (three-way, ram, valve) requires periodic adjustment and skill.
What loader does the Inception Designs Autococker (custom) need?
A force-feed loader (Dye Rotor, Virtue Spire) is needed for the Inception Designs Autococker (custom)'s fire rate. A gravity hopper limits you to ~6 BPS.
How much does the Inception Designs Autococker (custom) cost?
New: $1000 MSRP, typically $900-2000+ on the street. Used prices vary — check BST forums and eBay for current asking prices.
What barrel thread does the Inception Designs Autococker (custom) use?
The Inception Designs Autococker (custom) shoots .68 caliber. Confirm the specific thread pattern for your variant before ordering a barrel.
What firing modes does the Inception Designs Autococker (custom) support?
How heavy is the Inception Designs Autococker (custom)?
2.6 lbs unloaded. With a full hopper and HPA tank, expect roughly 5.1–6.1 lbs total.
Is the Inception Designs Autococker (custom) worth buying?
Hand-built custom Autocockers: the pinnacle of the classic timing-based platform, configurable as semi or pump for collectors and mech-class players. Strengths: Bespoke craftsmanship, Iconic platform. Trade-offs: Timing must be maintained, Not beginner-friendly.