An Autococker-threaded pump gun that ships ready to play with a smooth stroke and huge aftermarket barrel compatibility.
Technical Specifications
Operation
Pump (Autococker-platform)
Firing Modes
pump
Caliber
.68
Feed System
Vertical feed
Air Source
HPA/CO2
Operating Pressure
~250-300 psi
Weight (unloaded)
2.2 lbs
MSRP
$420
Street Price
$400-460
Maintenance
Low
Notable features: Autococker barrel threading, Smooth pump stroke, Ready-to-play out of box
Pros & Cons
Pros
Excellent all-around pump
Massive barrel compatibility
Solid build
Cons
Pricier than basic pumps
Single-shot pace
Best for: Pump players, Woodsball, Players wanting Cocker-thread barrels
Setup & First-Day Tuning Guide
Inspect the Pump Stroke — Before adding air, pull the pump handle back fully then push forward. On the Empire Sniper it should move smoothly — any roughness means the pump rod needs a coat of Dow 33 grease.
Check the Ball Detent — Inspect the ball detent that holds rounds in the breech. A worn detent is the #1 cause of ball drops in pump guns. It should offer clear resistance when pressed.
Dry-Cycle Before Air — With no air and no balls, pump-cycle 10 times to feel the trigger break. Commit to a full pump stroke every rep — short-stroking is the most common first-day jam and it's technique, not the gun.
Connect Air & Check Fittings — Thread on your HPA or CO2 tank slowly and listen at all connections for any hissing. The Empire Sniper runs well on either source — HPA gives more consistent velocity.
Chronograph to Your Field Limit — Fire 5 shots across the chronograph. Adjust the velocity screw inside the grip frame — clockwise raises, counter-clockwise lowers. Target 280 fps (confirm your field's limit). Pump guns typically run ±3–5 fps.
Load & Practice Full Pump Strokes — Load a 10-round tube and fire at a safe backstop. A confident, complete pump stroke eliminates 90% of field jams.
Maintenance Schedule
Interval
Task
Detail
After every outing
Barrel, bolt & exterior clean
Squeegee twice, bolt wipe, screws snug.
Every 5 sessions
Bolt O-ring lube & cup seal check
Clean with isopropyl, dry, apply Dow 33. Inspect cup seal — replace if deformed.
Every 6 months
Valve & fitting service
Re-lube all O-rings. Check all fittings and inline regulator if present.
Annually
Full teardown & O-ring replacement
Complete disassembly, full O-ring kit replacement, inspect springs.
Simple pump internals; periodic o-ring lube and barrel cleaning.
Common Problems & Troubleshooting
Pump drags or binds
Cause: Dry pump rod; over-tightened arm bolts
Fix: Apply Dow 33 to the pump rod and inside the pump arm guide. Check arm bolts are snug but not overtorqued.
Ball drops from breech
Cause: Worn ball detent
Fix: Check the ball detent on the Empire Sniper — replace if it offers no resistance. Detents cost under $5.
Gun won't cock
Cause: Worn pump-arm catch; broken spring
Fix: Inspect the catch pawl and pump return spring. Replace the spring if broken — available from the manufacturer.
Velocity drops suddenly
Cause: Cup seal failure; low tank pressure
Fix: Check tank pressure, then inspect the cup seal — replace if flat or cracked. Full O-ring kit is under $10.
Upgrade Path
Autococker-thread barrels
Regulator
Custom pump kit
Frequently Asked Questions
Is the Empire Sniper good for beginners?
Yes, with some paintball experience. The Empire Sniper rewards players who understand basic maintenance and operation.
Does the Empire Sniper run on CO2 or HPA?
Compatible with HPA/CO2. CO2 works but HPA gives significantly more consistent velocity and is better for long-term seal health.
What is the operating pressure of the Empire Sniper?
The Empire Sniper operates at ~250-300 psi. Match your regulator output to this spec.
How hard is the Empire Sniper to maintain?
Easy — basic bolt cleaning every few sessions. Simple pump internals; periodic o-ring lube and barrel cleaning.
What loader does the Empire Sniper need?
Pump guns use tubes or pods — no electronic loader needed.
How much does the Empire Sniper cost?
New: $420 MSRP, typically $400-460 on the street. Used prices vary — check BST forums and eBay for current asking prices.
What barrel thread does the Empire Sniper use?
The Empire Sniper shoots .68 caliber. Confirm the specific thread pattern for your variant before ordering a barrel.
What firing modes does the Empire Sniper support?
Supported modes: pump. Most recreational fields require semi-auto only.
How heavy is the Empire Sniper?
2.2 lbs unloaded. With a full hopper and HPA tank, expect roughly 4.7–5.7 lbs total.
Is the Empire Sniper worth buying?
An Autococker-threaded pump gun that ships ready to play with a smooth stroke and huge aftermarket barrel compatibility. Strengths: Excellent all-around pump, Massive barrel compatibility. Trade-offs: Pricier than basic pumps, Single-shot pace.